Learning how to install carpet may sound daunting! Professionally installing carpet by an experienced crew is now so expensive. But with the help of the right tools and some guidance, you can easily install carpets yourself. In today’s guide, we will discuss how to install a carpet on any surface. I have broken down the whole procedure into six simple steps. Make sure you collect all the necessary items required for installing the carpet. Apart from this, even you have to be prepared to take some time to get this job done perfectly. Without wasting much time, let us check out how to install carpet without installation labor.
How To Install Carpet?
You can follow these steps for how to install carpet by yourself.
- Measure Your Room
- Start Preparing The Subfloor
- Install Tack Strips
- Lay Carpet Padding On The Floor
- Staple The Carpet Padding With A Staple Gun
- Measure And Cut The Carpet
- Place The Carpet And Secure The Seams
- Seal It With A Carpet Roller
- Use A Knee Kicker To Stretch The Carpet
- Trim The Excess Using A Carpet Trimmer
- Use Carpet Chisel To Press The Carpet
There is a total of eleven steps in the procedure of how to install carpet. Installing a carpet requires a lot of patience and accuracy. Let me remind you it is not a one-day job. But if you have the right items and enough time, you can complete this task very quickly.
You can now continue to read to learn how to install carpet tiles.
Step By Step Guide For How To Install Carpet
In this section, I will explain and teach you how to install carpet on concrete and plywood.
Step 1: Measure Your Room
First, you have to start measuring the length and width of the room where you want to install the carpet. Then multiply these numbers to calculate the square footage of this room. Once you got the total square footage number, you can select the carpet’s size accordingly. Make sure your order 10 to 20% more carpet than you need.
Step 2: Start Preparing The Subfloor
Let’s now get ready for installing the carpet. With the help of a vacuum cleaner and sweep clean the area well. You must also remove the existing carpet or flooring if present. Ensure that you remove your old door band baseboards before starting. Also, check for moisture or damage to the floor including sunken spots and patches.
You can keep on reading to know how to install carpet tack strips.
Step 3: Install Tack Strip
It is now time to install carpet tack strips along every wall except entryways and doorways. While doing this procedure, make sure you leave half-inch space between the strip and the wall. For wood floors, simply nail the strip down. While for concrete surfaces, secure the tack strip with construction adhesive and masonry nails.
Step 4: Lay Carpet Padding On The Floor
Once the tack strips are installed, start rolling out the padding from one side of the room to the other side. Cut off the padding when you get to the other side of the wall. Make sure that the edges of the padding should go up to the edge of the tack strips. Also, check whether you’re matching up the seams evenly.
Step 5: Staple The Carpet Padding With A Staple Gun
With the help of a staple gun, press staples onto the carpet padding every 2 feet or more. Make sure you staple the padding along the inside edge of the tacking strip. You can use padding glue down underneath the padding for concrete floors. Lastly, use duct tape to tape down each seam together.
You can keep on reading to know how to install carpet on the floor.
Step 6: Measure And Cut The Carpet
Now, roll up the carpet with the backside facing outward on a plane surface. Give your carpet at least 24 hours to adjust to the temperature and humidity in your home. With the help of a utility knife, cut the carpet according to room measurements. Make sure you add an extra 6” to trim down extra ones. Otherwise cutting too short will waste the entire strip.
Step 7: Place The Carpet And Secure The Seams
Place the carpet against your wall by covering the floor and tack strips. When it comes to seam, you to keep the sticky part facing up. Place seaming tape down over the tape to make sure both edges are covered. Now, place a seaming iron underneath the carpet and on top of the tape for 8 to 10 seconds. Slowly press down on the part of seam so that carpet sticks to the tape.
Step 8: Seal With A Carpet Roller
To make the center of the seam secure in its place, you’ll need carpet rollers. Simply run them over several times running back and forth along the seam. Make sure you do this as you heat each section. Or else it will remain stuck in its place.
Step 9: Use A Knee Kicker To Stretch The Carpet
Place a knee kicker about 3 inches away from the wall on the carpet. Keep the flat vertical part sticking out on the other end. Using your knee, apply some force to stretch the carpet onto the strip. You can also use a carpet stretcher if you have a large room. Make sure you remove all the lumps out of the carpet and leave some excess carpet on each side.
Step 10: Trim The Excess Using A Carpet Trimmer
Once the carpet is attached, trim the excess from the edges using a wall carpet trimmer. You simply have to press the tool flat against the carpet. Keep the baseboard on the sharp side. Slowly push it along the wall by applying pressure. Make sure you check that you cleanly cut the carpet before taking the strip off.
Step 11: Use Carpet Chisel To Press The Carpet
For the last step, you’ll need a carpet chisel. This tool is a wide, dull blade. Basically, this tool lets you press the carpet in place. You can use it to wedge the carpet under the baseboard by pressing it into the carpet. Keep doing it until the carpet settles in place.
You can keep on reading to learn how to install carpets on stairs.
Guide To Install Carpet on Stairs
Usually, stairs are the most heavily used area in the home. You can easily decorate them with a fresh set of carpet. In this section, I will explain to you how to install carpet on stairs in short. Even though the process is similar to installing carpet on floors, have a look at this procedure.
Step 1: Measure Your Staircase
You have to measure your staircase including its length, width, and height. Make sure you also calculate the number of stairs to figure out how many sets of tackless strips you’ll need.
Step 2: Install Tackless Strips
First, you have to outline where you want to place your carpet. Using chalk, draw straight lines from the front to the back of the stair. Then cut your tackless strips to keep your carpet rooted to the ground. Carefully, hammer the strips into the center of each stair.
Step 3: Install Carpet Padding
Next, you have to measure and cut a piece of carpet pad for each tread. This carpet padding will give the carpet a pleasant feeling of cushion and softness. Make sure you cut every piece to be the same length as the tackless strips. And then staple them securely.
Step 4: Lay The Carpet Runner
It’s time to lay your carpet runner from the top and work your way down. You can trace the carpet outline using a pencil before placing them. Make sure you press the carpet under the nose and tug the rest out.
Step 5: Press The Carpet Using Carpet Knee-Kicker And Chisel
Using a carpet knee-kicker get the carpet planted firmly in areas that are difficult to reach. Make sure you apply enough pressure until the carpet is locked in. With the help of a carpet chisel, press the angle between the step’s height and tread.
Step 6: Cut Excess Carpet
Once you reached the bottom of the stairs, cut the excess carpet with a carpet knife. You can use a carpet glue or staple to finish things off.
List Of Carpet Laying Tools
Here, I have listed all the tools you’ll need for carpet installation.
- Track strips
- Staple gun (for wood surfaces)
- Utility knife
- Stair tool
- Chalk line
- Tape measure
- Duct tape
- Seaming tape
- Knee pads
- Rolling pin or carpet roller
- Seaming iron
- Cement-based waterproof filler (for a concrete floor)
- Construction adhesive (for a concrete floor)
- Masonry nails (for a concrete floor)
- Carpet adhesive (for a concrete floor)
If you want to know more topics like these visit Installmo
What Is The Process Of Installing Carpet?
Roll the carpet out.
Start in one corner of the room. Leave 3 to 4 inches (7.6 to 10.2 cm) of excess on each side of the carpet up against the wall. Unroll the carpet roll, covering the floor and tack strips as you do. Line up carpet edges as needed to make seams and cover the whole floor.
Can I Install Carpet By Myself?
With planning, careful measurements and the right specialized tools, DIY carpeting installation is possible. Installing carpet yourself can save you money as you upgrade your flooring.
Is It Cheaper To Install Carpet Yourself?
Based on this information, you can save about $700 to $1,000 by installing carpet yourself. The price varies depending on the price of the materials. Besides saving some money, you’ll get some more benefits by installing carpet yourself.
Does All Carpet Need To Be Stretched?
A carpet with no cuts or damage can still require a stretching. If you look down at the carpet, it may have visible lumps and wrinkles from years of use. For example, moving a long-standing piece of heavy furniture to another area can cause the carpet to warp in the original area.
Do You Have To Put Padding Under Carpet?
Carpet needs padding to protect the hard flooring surfaces underneath it, and most carpeting warranties are void without the proper padding underneath the flooring. Your carpet padding preserves your carpet against shedding from foot traffic and heavy furniture.
How Much Does It Cost To Carpet A 10×12 Room?
According to HomeAdvisor, you will pay between $3.50 to $11 per square foot to have carpet installed in your home. A 10 x 12 room amounts to 120 square feet, which means you’ll end up paying approximately $420 to $1,320 to have carpet installed. This includes the carpet, the padding, and the installation costs.
By reading my above post, you’ve learned how to install carpet with and without a stretcher in detail. You can easily install carpet in your living room and staircase on your own by following the above two procedures. Very few people know that carpets may expand or shrink depending on the weather. So, always make sure you let your carpet sit for 24 hours before you cut it down. This will give the carpet enough time to adjust to the temperature and humidity in your home. Thus, you can easily design your new home by understanding how to install carpet.
To Know Some Great Stuff Do Visit FactorsWeb
To Know Some Great Stuff Do Visit FeatureBuddies
To Know Some Great Stuff Do Visit FeedAtlas
To Know Some Great Stuff Do Visit FilmyViral
To Know Some Great Stuff Do Visit FinanceNInsurance